Pressure Washer Buying Guide: PSI, Flow and Nozzles
Stripping algae off a deck or road film off a driveway depends on two numbers working together: pressure in PSI and water volume in GPM. Pressure breaks the bond, flow carries the debris away, and multiplying the two gives cleaning units, the figure that actually predicts performance. Electric machines run quiet and start instantly, while gas models bring the muscle for large concrete. Nozzle selection then decides whether you clean the surface or carve into it.
Pressure, Flow, and Cleaning Units
PSI measures the force at the nozzle and GPM measures how much water passes through. A high PSI with low flow blasts a narrow spot but rinses slowly, while generous flow with moderate pressure clears wide areas faster.
Multiplying PSI by GPM gives cleaning units, a single figure that compares machines fairly. Light patio work sits under 4,000 units, general home use lands between 4,000 and 8,000, and heavy concrete and paint stripping climbs past that.
Electric Versus Gas Power
Electric units start with a switch, run quietly, need no oil changes, and can be used in a garage without fumes. They typically deliver 1,300 to 2,300 PSI, which handles cars, patio furniture, siding, and small decks comfortably.
Gas engines produce 2,500 to 4,400 PSI with higher flow, clearing large driveways and stripping old stain in a fraction of the time. They demand fuel, oil changes, pull starting, and outdoor use only, and they are considerably louder.
Pump Type and Durability
Axial cam pumps are common on consumer machines, compact and affordable, though they run hotter and generally last a few hundred hours. They are sealed units, so a failure usually means replacing the pump rather than rebuilding it.
Triplex pumps use three pistons with serviceable seals and run cooler at lower RPM, lasting thousands of hours. They cost more upfront and appear on prosumer and commercial machines, but they justify the price for anyone cleaning frequently.
Nozzles and Attachments
Quick-connect tips are color coded by spray angle: red at zero degrees, yellow at fifteen, green at twenty-five, white at forty, and black for low-pressure soap. The zero degree tip concentrates enough force to gouge wood and etch concrete, so it is rarely the right choice.
A surface cleaner attachment spins two nozzles under a shroud, cleaning driveways in even passes without the stripe pattern a wand leaves behind. Turbo nozzles rotate a zero degree stream in a cone, combining concentrated force with wider coverage for stubborn grime.
Hose, Cord, and Reach
Hose length determines how far you roam before moving the machine, with twenty-five feet typical and fifty feet far more convenient on a long driveway. Rubber hoses stay flexible in cold weather while plastic ones kink and fight you.
Electric models are limited by cord length and should be plugged directly into a grounded outlet rather than a light extension cord, which causes voltage drop and motor strain. Check whether the machine has a GFCI plug built in, since that is standard on outdoor electrical equipment.
Detergent, Storage, and Maintenance
Onboard detergent tanks or siphon tubes draw soap through the low-pressure black nozzle, letting cleaner sit and work before a rinse. Only use detergents labeled for pressure washers, since household soaps can damage seals.
Running the machine dry damages the pump, so always turn the water on first and release trapped pressure before disconnecting. Pump saver fluid protects seals over winter, and storing the unit above freezing prevents cracked components from ice expansion.
What to Check Before You Buy
- Multiply PSI by GPM to compare machines on cleaning units rather than pressure alone.
- Choose electric for cars, siding, and patios, or gas for driveways and stripping.
- Look for a triplex pump if you clean often and want a longer service life.
- Confirm the machine includes the nozzle angles you need plus a soap tip.
- Consider a surface cleaner attachment if you have a large concrete area.
- Check hose length and material, favoring longer rubber hoses that resist kinking.
- Verify the unit has a detergent tank or siphon and a GFCI plug if electric.
How to Choose a Pressure Washer
Sizing the machine to your largest regular cleaning job avoids both underpowered frustration and wasted money.
- Identify the toughest surface you clean and how large an area it covers.
- Set a target cleaning unit figure based on that job.
- Decide between electric convenience and gas power for the runtime you need.
- Choose a pump type based on how many hours a year you expect to run it.
- Confirm the nozzle set and any attachments match your surfaces.
- Check hose and cord reach against the distance from your water and power source.
Ready to shop? Browse our full list of Pressure Washers to compare current options and prices.
